1.1.11 试验结果   Test result
1.1.11.1 防空转试验   Anti-Idling Test
列车在静止状态满级加速起动，在加速过程中持续向轨面喷洒减摩液。
The train was started in full-staged acceleration from static state, and anti-friction liquid was continuously sprayed on the rail surface during the acceleration process.

图2.4-2为软件修改前的试验曲线，加速约55s后，列车速度仅为92km/h，而Mc2车1、2轴速度已上升至180km/h，可见MCM防空转功能、加速度限制功能已完全丧失；同时由于ATP、LKJ显示速度采用的是前进方向Mc2车的轴速信号，速度表显示数值已经不可信。通过厂家提供的列车参考速度信号可以看到，列车参考速度与最高空转速度一致。
The testing curve before modifying the software is shown in Fig.2.4-2. After accelerating for about 55s, the speed of the train is only 92km/h, while the speed of axles 1 and 2 of car Mc2 has increased to 180km/h. We can see that the anti-idling function of MCM and the acceleration restriction function are completely lost; meanwhile, the speed displayed by the ATP and LKJ are axle speed signal from car Mc2 in the forwarding direction, so the displayed value of speed can not be trusted anymore. We can see from the reference speed signal of train provided by the manufacturer that the reference speed of train is consistent with the maximum idling speed.
软件修改后进行了3次防空转性能试验，试验曲线分别见图2.4-3、2.4-4、2.4-5。从图中可以看出，动车组防空转功能正常，列车参考速度与GPS速度基本一致。在司机显示屏MCM界面可以看到MCM输出调节变化。
After modifying the software, the anti-idling performance test was conducted for three times, and the testing curves are shown in Fig.2.4-3, Fig.2.4-4 and Fig.2.4-5.  We can see from these Figures that, the anti-idling function of MU is normal, and the reference speed of train is basically consistent with the GPS speed.  The output regulation changes of MCM can be see from the MCM interface on the driver’s display screen.
1.1.11.2 防滑行试验   Anti-Sliding Test 

华译网北京翻译公司翻译过有关动车组防空转试验技术文件资料,Beijing Chinese Translation Service Company has translated many technical documents of Computational method of MU Anti-Idling Test
试验曲线分别见图2.4-6、2.4-7、2.4-8。三次试验中，当滑行时间较长时，MCM均自动封锁，防滑行功能由空气系统实现，在司机显示屏的机械制动界面可以看到Mc2车发生滑行的轴电制动封锁，机械制动力变化调节。
 The testing curves are shown in Fig.2.4-6, Fig.2.4-7 and Fig.2.4-8.  During all three tests, MCM would automatically blocked if the sliding time is long enough. The anti-sliding function is realized by the air system. The axle electric braking blocking and the variation regulation of mechanical braking force during the sliding of car Mc2 can be seen on the mechanical braking interface of the driver’s display screen.
1.1.12 试验结论  Test conclusion
动车组防空转功能正常。
The anti-idling function of the MU is normal.
动车组动轴发生持续滑行时，电制动会发生封锁，此时防滑功能由空气系统实现。
During the continuous sliding of driving axle of MU, the electric brake will block, at this time, the anti-sliding function can be realized by the air system.
试验后，未出现擦轮或者钢轨擦伤现象，符合试验大纲要求。
After the test, there are no wheel friction or rail scratching problems, and this complies with the requirements of the test outline.